Search Results for: Tweed Bassman

Founded in the mid-1940s in Fullerton, California by Leo Fender, the legendary amps produced by this company have been heard on countless recordings and are influential on countless other amp makers. In the beginning Fender paired small combo amps with lap steels and electric guitars aimed at student players, but word of the superior tone and build quality quickly spread among professional musicians. In over seventy years of existence, Fender has consistently evolved and innovated its sound from the Tweed era through the Brown and Blackface eras and beyond.

Mercury Magnetics has built a massive collection of ToneClone® Transformers and Chokes for Fender Amps available from all eras of production. Answering the needs of players and amp-builders alike, our extensive catalog of audio transformers is the ultimate resource whether you’re looking to replace a worn-out transformer in a vintage Fender amp or looking to nail a vintage tone in a new amp or amp build. The engineers at Mercury have painstakingly documented every detail and nuance of the best-of-breed vintage transformers and can faithfully produce perfect clones using the same materials and methods used on the originals.

The ToneClone+ Series from Mercury Magnetics adds more utility and options without altering the original tone. Love your amp but want to change your speaker configuration? Mercury’s ToneClone+ Output Transformers give players more impedance options like alternate and multi-tapped secondaries. Power Transformers can benefit from the “Plus” treatment as well with alternate primary voltage, Higher or Lower B+ Voltages, added current capability, and more.

Fender Woodie Amp Transformers: The earliest production amps to come out of Fullerton, Fender ‘Woodie’ amps can be identified by their hardwood cabinets and fixed handles. We are proud to offer ToneClone® transformers from this short-lived and rare Woodie era including the Woodie Deluxe (aka Model 26) and Woodie Pro.

Fender Tweed Amp Transformers: The Fender Tweed era lasted from the late forties to early sixties and a vast amount of artists from all generations have crafted their distinct tone using these amps through all genres. Notable artists include: Scotty Moore (Elvis Presley), Neil Young, Larry Carlton, Eric Clapton and Keith Richards. Mercury Magnetics has the largest catalog of vintage-correct Fender ToneClone® replacements transformers for the following models: Tweed Bandmaster, Tweed Bassman, Tweed Champ, Tweed Harvard, Tweed Princeton, Tweed Pro/Dual Professional, Tweed Super, Tweed Tremolux, Tweed Deluxe, Tweed Twin, and Tweed Vibrolux.

Fender Blonde and Brown (Brownface) Amp Transformers: Sitting on the timeline between the Tweed and Blackface Fender amps, the Blonde/Brown amps of the early sixties were most noticeably embraced by surf groups like the Beach Boys and Dick Dale. Our catalog of ToneClone® amp transformers for this era includes Brown/Blonde Bandmaster, Blonde Bassman, Blonde Showman, Blonde Tremolux, Blonde Twin, Brown Concert, Brown Deluxe, Brown Princeton, Brown Pro, Brown Super, Brown Vibrasonic, Brown Vibrolux, and Brown Vibroverb. Also see our transformers and choke for the 6G15 Reverb Unit.

Fender Blackface Amp Transformers: Easily distinguishable by their black control plates and white lettering, Fender Blackface amps began showing up on stages and recordings in the early-mid 1960s. Extremely popular among musicians then, the impressive build quality and versatile tones have kept these classic amps popular even 50 years later. Mercury Magnetics has hundreds of ToneClone® and ToneClone+ transformers and chokes for Fender Blackface Amps including: Blackface Bandmaster/Bandmaster Reverb, Blackface Bassman, Blackface Champ, Blackface Concert, Blackface Deluxe/Deluxe Reverb, Blackface Princeton/Princeton Reverb, Blackface Pro/Pro Reverb, Blackface Showman, Blackface Tremolux, Blackface Twin Reverb, Blackface Vibrochamp, Blackface Vibrolux, and Blackface Vibroverb. Also see our transformers and choke for the 6G15 Reverb Unit.

We told this was coming.. Tes, when readers ask us to review something, we do our best to respond, and thanks to RedPlate founder Henry Heistand, we received two RedPlates for review. We’ll start this episode by telling  you that Henry Heistand appears to be a very clever fellow who is not working in the shadows of that past, which is to say that he builds feature-rich amplifiers that in no way pretend to be vintage knock-offs. Play a RedPlate and you’re firmly treading in the present, rather than mining tone out of a dusty box built by a dead man (or woman—sorry Lily). And that’s fine. There is certainly ample space in these pages for the living, and RedPlates are in fact very lively tools indeed. We asked Henry to give us a glimpse into his background and motivation, and our reviews of the TweedyVerb and BlackVerb follow….

TQR: How and when did you initially become involved in electronics and amplification?

HH: Starting around age 12 playing to the radio and jamming with friends, my first build attempt was a speaker cabinet made out of ½ plywood and covered with yellow carpeting. It had a leopard (spotted) grill cloth and contained 6 speakers recycled from various old TVs and stereos. My first real amp repair was replacing a screen resistor in a Fender Bassman in 1970. I went to college for a year and then played guitar full time until 1979 when I attended electronics school (they still taught tubes). To pay for school I got a part time job at a church organ repair shop that had a “combo” repair department and still played in club bands on weekends. Attending electronics school in the morning and repairing gear in the afternoons was a great way to instantly translate the classroom to the real world. Compared to the tube TVs and tube broadcast transmitters, the tube musical amplifiers were relatively simple. Besides Fender and Marshall, tube amps by Sunn, Ampeg, Gibson, West, Park, Hiwatt, Sound City and all the Supro/Kalamazoo/Dan Electro stuff. If I only had a nickel for every good tube I tossed in the trash back then. Many of those same companies had solid-state amps too along with companies like Acoustic, Kustom, Peavey, Randall, Lab, SG and Roland. It seems like the ’70s was the golden era of guitar amp designers. Although most tube amps have a similar topology, the differences between brands in those days ranged from truly innovative to laughable. On a few occasions when a solid-state repair would come in that was totally fubar, one of the church organ repair guys would show me how to design a new circuit right over the top of the problem area, teaching me the value of having a few simple circuit designs at the ready for emergencies. In late ’82 I got a career job in the computer field, and by ’86 purchased the part of the church organ repair shop that repaired the “combo” gear. The new company was named Music Mechanix and kept the warranty contracts with all the majors for amps, keyboards and P.A.s.

TQR: As you became more familiar with various amp designs of the past, what were your favorites and why?

HH: Thinking back to the tonal memories accumulated during those years spent repairing amps, the most musical of all of them were probably the early ’60s Fender tube amps. In addition to repairs, Music Mechanix did all the popular mods of the day (anyone remember the original Train Wreck Mod pages for Fenders?), many times we would redo almost everything inside but keeping the exterior unchanged. Most of my playing back then was strictly radio cover songs so the quest was always to find the one amp that could imitate everything. Music Mechanix was continuing the warranty station status from the previous owner (established in the ’50s) so every original manufacturer’s amplifier schematic ever released was available as a reference source, residing in 16 large file cabinets. On the side, I kept a little notebook of circuits and mods of interest to use as building blocks.

TQR: Can you describe the lasting impressions created by your study of the experiences with classic amps that have most affected your own design philosophy and preferences?

HH: As a service to friends and regular customers Music Mechanix would take a classic amp (at the time it was easy to get something like a used Bassman for $100) and do Frankenstein amps that were Fender this, Marshall that, with a sprinkling of Vox and Ampeg thrown in depending on the customer’s needs. On the weekends I was doing gigs using a pair of modified Ampeg VT-40s in stereo until somehow I ended up with a Mesa Boogie S.O.B. that had a really innovative phase inverter section controlled by a “LIMIT” knob. A bizarre variation of a PI section’s constant current source, the circuit was not in the RCA manual or on any other schematic. It sparked something in me and from hen on I started doing creative amp mods that were not copies of things I had seen on schematics.

TQR: When did you first begin to sketch out the concept for RedPlate amps, and what did you want to accomplish that would be unique and different?

HH: I had always been fascinated with “sleeper” amps that looked small but sounded big. After selling the repair business I used my free time to do a lot of experimentation on point-to-point builds in a Fender Camp sized chassis, eventually working out how to do a 7 tube, large transformer build in a Champ chassis without noise or oscillation. My favorite guitar tones were the recorded sounds of the Mesa Boogie/Dumble ODS type amps (even before I even knew what a Dumble amp was). A clean singing tone with a hint of character that sustains and blooms is my idea of the ultimate tone and the design goal of all the RedPlate models.

TQR: Can you briefly describe the unique features and differences among the current line of RedPlate models?

HH: RedPlate probably has too many models because we treat the sections as modular building blocks. We start with one of the 3 chassis sizes:

CH1. 15” width with four 9 pin sockets and two 8 pin sockets, transformers up to the 50 watt size.

CH2: 17” width with six 9 pin sockets and two 8 pin sockets, transformers up to 80 watt size.

CH3: 19” width with five 9 pin sockets and four 8 pin sockets, transformers up to 160 watts

Then we use different combinations of the building blocks with the only limitation being the number of controls (physical knob space) and the number of tube sockets available. Building blocks currently in use:

BB1. PREAMP1—Tweed—A single tone knob preamp (Tweed style).

BB2. PREAMP2—Blackface—A Treble, Middle, Bass Preamp (Blackface style).

BB3. DRIVE1—A three knob overdrive section (Gain, Drive, and Level).

BB4. DRIVE2—A six knob overdrive section (Gain, Drive, Level, Treble, Middle and Bass).

BB5. REVERB—A single knob tube reverb with medium decay tank.

BB6. EFFECTS LOOP—A fully buffered serial loop, return level is the master volume.

BB7. PHASE INVERTER—Standard Long Tail pair, very similar to the early ’60s designs.

BB8. POWER AMP #1—40 watts cathode bias (6L6GC).

BB9. POWER AMP #2—50 watts fixed bias/40 watts cathode bias (6V6GC)

BB10. POWER AMP #3—80 watts fixed bias (KT-88).

BB11. POWER AMP #4—45 watts fixed bias/18 watts cathode bias (6V6GTA)

BB12. POWER AMP #5—100 watts fixed/50 watts fixed (6L6GC).

TQR: Both of our review amps are loaded with Warehouse speakers from Kentucky, which we have reviewed before. How extensive are your evaluations of various speakers when creating a new model? Does the same process apply with transformers, tubes or other components?

HH: The current lineup is using WGS Retro 30, WGS British Lead 80 and Eminence Swamp Thang speakers in the combo amps. The decision to use these was based on side-by-side comparisons with other brands (an ongoing process).

Tube selection is mostly based on reliability (as long as the tone is still there). The current production amps use Svetlana 6L6GC, SovTek 12AX7LP (PI tube), and Electro Harmonix 6V6GTA and 12AX7s (preamp).

Selecting individual signal path components is more difficult because side-by-side comparisons can be misleading (no 2 amps are exactly alike). The signal path in current production amps use PS series Orange Drop capacitors and carbon film resistors based on low noise and musical warmth in the tone. RedPlate Amps has a good relationship with Mercury Magnetics and I like to use their transformers in most models.

TQR: How does the half power switch function in your amps, as well as the “mode” control and various voicing controls?

HH: Depending on the output section, 3 methods are used:

1. 6L6GC 100 watt/50 watt—The switch lifts two of the four tubes by 10K so they are effectively out of the circuit yet the impedance selection is still valid.

2. 6V6GTA 45 watt/18 watt—Full power runs two of the tube in cathode bias and two in fixed bias, the switch lifts the fixed bias tubes by 10K to effectively remove them without changing the output impedance.

3. 17 Watt (Hi/Lower)—This switch just lowers the voltage to the phase inverter tube so the amp breaks up sooner. There are two different styles of mode switches. On the Tweed style preamps the 6 position mode regressively reduces midrange and preamp output to imitate a Blackface style amp. On the Blackface style preamp the 6 position mode switch progressively fattens the midrange to imitate a Tweed style amp. Most of the models also include a Humbucking/single coil switch to set the amount of bass gain in the input stage.

TQR: How much individual customization or voicing do you offer for specific models when working with an artist?

HH: Unlimited customization is available, although most of the professionals that use RedPlate Amps are content playing standard models.

TQR: We noticed that you include the owner’s name on the back panel, correct? A nice touch…

HH: Yeah, the front and rear panels are done in-house, we could even put pictures of your dog on there.

TQR: What do you want to accomplish in the future? New models?

HH: “Amps that sing” being every guitar player! Going forward, curiosity and customer feedback will continue to drive the evolution of current designs and the development of new designs. For example, there will be a “shredder” amp in the near future (The ShredPlate) and possibly a bass amp. As RedPlate continues to gain name recognition with the music industry, models like the BlackVerb, MagicDust and TweedyVerb will hopefully be taken for granted as standard amplifier types.

The front and rear panels on the BlackVerb reveal an impressive array of controls, push/pull-knobs and switched pots. In fact, the printed operation guide includes a signal path diagram on the front page with a welcoming invitation to skip an in-depth review of the manual and just set all the knobs at 12 noon and play, which we did, consulting the manual as needed as we spent more time with the amp. So, is the BlackVerb too complicated for you “plug & play” guys? Not really, but the control panel is best reviewed in sections. You’re essentially working with a clean preamp circuit and a Drive section that includes Gain, Drive and Level controls for variable levels of distortion overdriven tones, but there are still many more additional tweakable features lurking within…

The first control adjacent to the single front input jack is the miniature Bright switch toggle with the center position OFF, Down producing the sound of “new strings” (an accurate description we might add), and Up rendering a brighter tone that will be familiar to those of you with a Fender Blackface amp with bright switch. We usually use the bright switch to put a little extra shimmer and spank on humbucking pickups, or neck pickups on single coils.

The Volume control includes a pull switch to engage a midrange boost that increases upper mids. The Middle control does what you’d expect, with a pull switch for a “Deep” setting that scoops mids and boosts bass frequencies—an excellent change-up for clean tones. The Bass control handles low end quite well, and it can be clicked OFF to be removed from the tone stack. Try that with a neck pickup and it produces the odd and very different EQ found in some old Valco and Gibson amps.

The Mod Selector is a 6-position rotary EQ switch that gradually produces a fatter, thicker tone as you rotate left to right from the “Funk” setting, to “Normal” and “Fat” (tweed). All this pulling and turning may sound complicated, but you’ll have it thoroughly digested in 5 minutes, and most importantly, these extra EQ controls expand the tonal capabilities of the BlackVerb in a clever and creative way that really is worth using and exploring. We have bitched about such bells and whistles on other amps having limited value, but no such questionable affectations plague the BlackVerb. Like we said, Henry is a clever fellow. On the Drive section…

This is where you mine and manage overdriven tones and distortion. The Gain control can be bypassed by clicking fully left, otherwise, you’re setting the amount of signal being sent to the first gain stage, which produces variable levels of smooth growl and grunt. The Drive control further ramps up distortion through two gain stages, and a pull switch on the knob serves as an afterburner for maximum burn and rip. At this point you will be channeling Metallica at full husky, so hide the dog. The Level control sets the output volume for this section, resulting in a progressively bigger, thicker, bolder voice. Of course, the big selling point for the BlackVerb is how all of your clean, moderately busted up and filthy dirty tones can be deftly tweaked and the volume managed with the Volume and Master volume controls. At the full power setting, you really can get this thing to sound like a 100 watt high gain amp on “7” at low decibel levels suitable for home recording and friendlier sound pressure levels.

The reverb control is what it is, and you can turn it off fully left and it’s out of the circuit. The Presence control is described as using “global negative feedback to remove low frequencies which frees up bandwidth for more midrange and highs,” and it can also be turned off when rotated fully left. Frankly, the appeal of this control escaped us, but we can imagine how it might be useful in a live situation where you may want to avoid too much low end muddying up the mix with bass and drums. The Master volume works very well without producing the dreaded master volume/low volume faux zizzz when you’re trying to light a fire at low volume levels.

One of our favorite features is the 50 watt/40 watt switch on the back panel that changes the boas from fixed to cathode for a completely different feel. With the 40 watt cathode biased setting you can also change the 6L6 output tubes to 6V6s, transforming the BlackVerb into an 18 watt cathode biased flame thrower, or bypassing the Gain section for a more tweedy character and voice. The Hi/Lo power switch changes the voltage on the input stage and the threshold for clean headroom.

The back panel Smooth switch is just that, adding slight compression in the clean preamp, and the Humbucker/Single Coil setting sets the amount of bass gain in the input stage, relieving you of perhaps resetting EQ when switching from single coils to humbuckers.

Additional utilitarian features on the back panel include a handy bias adjustment and test point, speaker impedance selector, main and extension speaker jacks, FX send and return, and footswitch jack. The footswitch gives you the capability to get in and out of the Tweed, Drive and Boost circuits. Tweed boosts upper mids while lifting the midrange control on the front panel for maximum push in the frequencies where the guitar really lies on stage. Drive engages the Drive feature, bypassing it when off at the footswitch. Boost makes everything sound bigger with a partial tone stack lift.

And now for the bottom line…. It seems to us that the intention of the BlackVerb is to be as tonefully versatile as a 1×12 combo amp can possibly be whether you are playing small clubs, bigger rooms or wide open outdoor stages. You could play nothing but smooth, clean jazz through this amp without ever venturing into the gain stages and be perfectly happy. Or you could do nothing but feast off the considerable gain and distortion lurking in the heart of the BlackVerb and be equally happy. Most gigging musicians want to range between such extremes living somewhere in the middle, and you can do that, too. Like most feature-rich amplifiers, you’ll find certain favorite settings that will be revisited with specific guitars, and after a few days you’ll have no trouble quickly accessing those settings, although the control panel is a bit difficult to read until you no longer need to read it at all.

The standard Warehouse Retro 30 speaker is a brighter version of the Veteran 30 we have favorably reviewed in the past. Given the considerable range of overdrive and distortion available in the BlackVerb, the Retro 30’s clear, articulate character and exceptional capacity to handle low frequencies makes it an excellent choice for this amplifier. Even at extreme gain and drive settings, the BlackVerb produces a rich and musical burn that does not mask or obscure essential overtones and harmonics. The clean tones are equally strong, powerful and clear, and the amp will nimbly spill into overdrive played clean at higher volume levels that can be managed with the volume on the guitar. The BlackVerb impressed with its ability to embody many different styles of amplifiers in one compact box, limited only by your capacity for experimentation and your imagination. Imagine that.

We were particularly anxious to experience the TweedyVerb because it seems to fit the power and volume requirements of so many players today, and it is a very straightforward and versatile 1×12 combo that is a breeze to hump to the next gig. Got your attention there, did we? We finally figured out why vintage blackface Pro Reverb amps have remained relatively underpriced… just pick one up.

The TweedyVerb is a cathode biased dual 6L6 amp with reverb, loaded with an 80 watt Warehouse British Lead 12” speaker. You won’t find a bad tone in this amp, and the controls are very intuitive, delivering outstanding “blackface,” “brown” and “tweed” tones via a 6-position Mode switch. The Bright switch is identical to the BlackVerb (you’ll love the “new strings” setting), with a single Volume control, simple Gain control, and a Tone control that can be clicked off fully left to bypass the tone stack for a very heavy and thick does of overdriven tones with excellent dynamic feel and touch sensitivity. The spring reverb is good—delivered form an original new old stock Accutronics pan made by Cary, IL, and the Presence control is identical to the BlackVerb, using global negative feedback to remove low frequencies and emphasize mids and highs. It also seems to decrease volume and gain, best used in our opinion for clean tones.

The 40 watt/17 watt switch on the back panel changes the voltage on the phase inverter. We preferred the sound and girth of the 40 watt setting, which still allows plenty of room for managing volume and variable distortion with the Gain and Volume controls, but the 17 watt setting is fine, too for close quarters. 6V6 power tubes can also be used at this setting without re-biasing for lower power output and volume. A footswitch is included to access both the fat Tweed setting on the Mode switch on the fly, and the Boost function, which acts as a tone stack bypass. Despite its compact size and relatively light weight, the TweedyVerb is a big-sounding amp that produces outstanding clean tones at usable stage volume, yet it can also be gradually pushed into the familiar sound of a Deluxe Reverb on “6” or even a vintage Marshall head at higher volume and gain settings. It’s a right fair chameleon, this one.

The Warehouse 80 watt British Lead 12 gracefully handles the power output of the TweedyVerb with excellent clarity, sold bass, vivid mids and a sweet and chimey top end. Like the BlackVerb, the TweedyVerb offers the sound and feel of several distinctively different amps in one box via the Mode switch, and we liked them all, from the rough and tumble Tweed, the slightly less raucous, smooth upper mid voice of the Brow, and the more scooped, open and airy Black settings. Both RedPlate models reviewed here clearly share the same DNA, which is to say that they possess a remarkably rich and music character, whether you choose to stroke big clean tones through them or dial up a tone that would make Billy Gibbons proud. Douse that light, and Quest forth….

View PDF Article

We always maintain a steady flow of gear arriving for review, but sometimes we also employ a fascinating if time-consuming research strategy that involves logging onto eBay, picking a broad category such as “guitar amplifiers,” and settling in for as long as it takes to patiently scroll through every page of listings. Yeah, that’s often 50 pages or more, but since we can’t possibly think of all the items that might interest us and search for them by name, it’s far more revealing and productive to just hunker down and scroll. Rarely do we fail to find something intriguing that would have otherwise been missed, and such was the case on a morning in August when we stumbled on a listing for a 1959 tweed Deluxe. Were we looking for a tweed Deluxe? Nope. Wouldn’t have crossed our mind at the time…. We had already reviewed 5E3 reproductions from Fender, Clark and Louis Electric within the past 3 years, and we have frequently referenced our 1958 Tremolux as being our desert island #1. Isn’t a Tremolux just a tweed Deluxe with tremolo in a bigger box? No… not even close. That would be like saying you wanted to date a blonde – any blonde. For the record, our fixed bias Tremolux possesses a cleaner tone with a bigger, booming voice created by the taller Pro cabinet. The Two Fifty Nine is a completely different animal….

Sporting a February 1959 date code on the tube chart, the ’59 had been listed by a seller in Arkansas who turned out to be Tut Campbell, formerly a well-known guitar dealer in Atlanta. Still buying and selling gear, Campbell had described the Deluxe as being in original condition with the exception of a replace output transformer – a big old mono block Stancor dating to 1957. Given the otherwise original condition of the Deluxe, which included the Jensen P12R, we made Campbell a “best off” below his asking price and scored the amp for $1,850 shipped. We wouldn’t say we stole the Deluxe, but it seemed a fair price of admission for the opportunity to experience and explore still another rare classic and supremely worthy piece of Fender history on your behalf.

The Deluxe arrived with the big Stancor dangling from the chassis despite Campbell’s careful packaging. Wasn’t his fault, really – in a feeble effort to avoid any additional holes being drilled in the chassis, the fellow who installed the Stancor in the ’60s had merely tightened set screws over the small tabs at the base of the heavy tranny, which was designed to be mounted upright – not hanging upside down in a guitar amplifier. Of more concern was the fact that while the amp was lighting up, there was no sound…. Well, we’ve been here before, so we made a call to God’s Country and the Columbus, Indiana domicile of Terry Dobbs – Mr. Valco to you. We had already set aside a spare output transformer (Lenco, McHenry, IL) that had been the original replacement installed in our ’58 Tremolux when we first received it, replaced with a Mercury Magneticsfor our June ’07 review article. Mr. Valco cheerfully answered his phone and as we explained the situation with the Deluxe he agreed to walk us through the installation of the new replacement – a simple process involving four lead wires being connected to the rectifier and output tube sockets, and the speaker jack. As long as you put the correct wires in the right place, a piece of cake, and we had the new tranny in within 10 minutes. Pilot lamp and all tubes glowing, still no sound…. Valco patiently guided us through a series of diagnostics with the multi-meter and the Deluxe was running on all cylinders, pumping 380 volts. Stumped, and with the hour growing late, we called it a day. Leaving the mysteriously neutered Deluxe chassis on the bench until tomorrow.

Morning came with a whining voice delivering a plaintive wake up call – “It’s got to be something stupid and simple….” Inspired by a huge steaming mug of Jamaican High Mountain meth, we sat back down at the bench, tilted the innards of the Deluxe chassis forward beneath a bright halogen desk lamp and peered in for answers. We began slowly examining the chassis in sections, looking for broken or dull solder joints, loose or broken wires, while gently pushing and prodding wires and connections with the eraser tip of a #2 pencil as we had seen Jeff Bakos do so often at his bench. After ten minutes or so we were about to give up, when we turned our attention to several places where the circuit was grounded to the chassis adjacent to the volume and tone pots, and damned if a solder joint for one of the uninsulated ground wires hadn’t separated from the chassis. No ground, no sound, and as soon as we had restored the solder joint the Two Fifty Nine arose from the dead with a mighty A major roar.

The amp was indeed remarkably well-preserved in all respects, with the typical amber patina of old tweed. The burnished chrome control panel remained bright and clean with no corrosion, the original handle remained intact, and a couple of small ciggie burns on the edge of the cabinet added a stamp of historic legitimacy to the Deluxe’s pedigree. The top half of the Jensen’s frame was coated in a fine film of red clay dust from the Delta, and while the cone was in remarkably good shape with no tears, an audible voice coil rub called for a recone. We would send the speaker to Tom Colvin’s Speaker Workshop in Ft. Wayne, Indiana, requesting that he leave the original unbroken solder joints for the speaker wires intact if possible.

Meanwhile the first order of business was to listen to an assortment of NOS tubes from our stash, and audition no less than a half dozen speakers. Different sets of power tubes and individual preamp tubes will sound surprisingly different, so we started out with a matched pair of NOS RCA 6V6s, a GE 5Y3 rectifier, and an RCA 12AX7 and 12AY7. From there we subbed in a dozen different RCA, Amperex, Tesla and GE 12AX7s, noting varying levels of brightness, warmth and intensity among them all. For an edgier, more aggressive voice, the GEs and Amperex typically deliver the goods, while RCAs produce a slightly warmer, richer, fuller tone. We also experimented with a 12AT7 and 12AX7 in place of the lower gain 12AY7, and while those tubes ramp up gain and distortion faster and with more intensity than the 12AY7, they seemed like overkill for us. Our Deluxe possesses a tone of gain using the stock 12AY7.

Rather than repeatedly reloading the Deluxe with different speakers, we used a Bob Burt 1×12 cabinet built from 100-year-old pine for our speaker tests. The original Jensen had never been pulled from our amp, but multiple speaker replacements in an old Fender inevitably cause the speaker mounting screws to loosen in the baffleboard, making speaker swaps unnecessarily clumsy and complicated. When we do run into loose mounting screws, we simply run a few small drops of Super Glue around the base of the screw and surrounding wood. Allow to dry and your screws will stay put provided that you don’t torque the nuts on the mounting screws like an idiot with a socket wrench. Don’t be that guy,

We tested a range of speakers that included a Celestion G12H 70thAnniversary, Colvin-reconed ’64 Jensen C12N, Eminence Wizard, Private Jack, Alnico Red Fang, Teas Heat, Screaming Eagle, Red, White & Blues, and Warehouse Green Beret, Veteran 30, Alnico Blackhawk and Alnico Black & Blue. The Alnico speakers generally produce a tighter, smoother, slightly more compressed tone, with a variable emphasis on upper mid-range and treble frequencies, while the speakers with ceramic magnets possess a wider, more open sound. Higher power ratings of 75W-100W offered by the Red, White & Blues, Screaming Eagle and Warehouse Blackhawk typically translate into more graceful handling of bass frequencies, and in a 20 watt Deluxe, zero speaker distortion, for a clean, powerful voice.

Let’s cut to the chase with speaker evaluations, shall we? It has become clear to us that even after reviewing a dozen speakers in as much detail as mere words allow in a single article, many of you remain uncertain about which speaker to choose. No kidding. We would absolutely love to hand you a single magic bullet when it comes to speaker swaps, but here’s the dirty little secret about choosing speakers…. The overall character of the amp you will be installing your new speaker in is critical, and to some extent, the type of guitars and pickups you play most often are important, too. Tailoring your sound with the unique gear you play is not a one-size fits-all proposition – you have to invest some thought into the process. Are you going for a classic “scooped” American Fendery tone, or something more British, with a bit of an aggressive edge and upper midrange voice? Are you playing guitars with single coil pickups or humbuckers? Is there a specific, signature tone you are searching for, or are you playing a wide variety of musical styles that requires a broader range of tones? Do you like the more open sound of speakers with ceramic magnets, or the smoother compression of Alnico? What are you not hearing from your amp and the speaker that’s in it now? Do you want a brighter tone, darker, better bass response, or fuller, more prominent mids? Do you want to really drive the speaker and hear it contributing to the overdriven sound of your amp, or do you want a big, clean tone with no speaker distortion in the mix? The truth is, if you don’t know what you want, you are far less likely to get it. On the other hand, nothing is accomplished with paralysis by analysis. To be perfectly honest, there are lots of speakers made by Celestion, Eminence, Warehouse and, if you can wait long enough for them to break in, Jensen, that we could and would be perfectly happy with, but we would also choose them carefully, taking into account all the factors mentioned above. After a couple of days spent swapping speakers, we ultimately concluded that we preferred the ’64 C12N for a classic tweed Deluxe tone, and a broken-in Celestion G12H 70th Anniversary for the most mind-altering 18 watt Marshall tone we have ever heard. Seriously. More on that in a minute….

Having split more than a few hairs with our speaker swaps, it was time to start picking nits off of gnats with some output transformer evaluations. We first contacted Dave Allen of Allen Amplification, who also stocks Heyboer transformers built to his specs. We found a variety of appropriate output transformers on Allen’s site that offered subtle variations on a stock original Deluxe OT, and we asked Dave to describe the TO26 model we wished to try in the Deluxe:

“The TO26 was intended as a hot rodding upgrade to a stock Deluxe Reverb OT. While maintaining the stock 3-1/8” mounting centers, its fat stack of hotter core steel and multi-tap secondary make it a good choice for builders wanting to maximize the performance of a pair of 6V6s and who may also want to push the envelope with 6L6/5881s while still being able to clear the speaker in a stock cabinet. There are physical limitations in small amps, so its short low profile is welcome. The orientation of the laminations is also good for low hum pick up from the power transformer. I found that an OT mounted the tall way (like my TO30D) picks up considerably more hum simply due to its orientation to the power transformer, so, shoe-horning a ‘tallish’ OT into your amp may cause it to pick up hum from the power transformer – not much of an upgrade. “The TO26’s 7K to 8 or 16 ohm rating makes it ideal for a pair of 6V6s as well as 3,500 ohm to 4 or 8 rating for 6L6/5881s. Notice you always have an 8 ohm option with both types of power tubes. An impedance switch could be wired (I use a blackface grounding switch) as a power tube type selector for an 8 ohm speaker to go between 6V6s and 6L6s. The TO26 will typically give slightly more output with 6V6s due to its more efficient low-loss core steel and will keep the bass clean longer for more perceived clean headroom. As it takes the most watts to reproduce the bass, you notice distortion there first, and since Fender-type amps are so bass heavy, you can quickly hit the wall with headroom, so a noticeable increase in clean bass response certainly feels like a more powerful amp with the TO26. It is kind of like you installed a new speaker with a larger ceramic magnet that is more efficient than the old speaker. The amp is a little louder and the bass a little tighter or cleaner.

“There seem to be a lot of 6L6-based 5E3 amps out there now to get a little clean headroom from a circuit normally not known for much of that. The TO26 is a good choice for that type of amp as it will fit typical available chassis and cabinets. It has extra long 12” topcoat leads ready to strip and solder. I would reckon it would handle up to about 30 watts before starting to saturate and compress – plenty of cathode-biased 6L6s. I find that the Heyboer paper stick-wound and interleaved output transformers with premium core steel and heavy core stacks have typically better clarity or definition than ‘stock’ OTs. Call it fidelity or whatever you want – just clearer distorted and complex tones and better separation of notes in chords, etc. I use the TO26 in the Allen Sweet Spot, Accomplice Jr. and Hot Fudge with Nuts amps with excellent results. All of these amps can use either 6V6 or 6L6 power tubes. You know how a 5F6-A or Super Reverb has that huge 4 bolt OT for a pair of 6L6s to get the maximum clean bottom end? That is sort of what the TO26’s OT is to a pair of 6V6s. It just doesn’t even come close to saturating.

When we informed Dave that we planned to run the Deluxe with 6L6/5881 power tubes as well as 6V6s, he recommended that we try the TO26 since it had been specifically designed for such applications. He also sent a smaller TO20 transformer, described as being designed with a wider 1-1/4′′ lamination “fat stack” that provides 60% additional core mass than typical ¾′′ stack units for improved performance. The TO20 is a direct replacement for Blues Jr. and Princeton Reverb amps, and also suitable for dual EL-84 amps with an 8 ohm load.

Mr. Valco also sent us a replacement 5E3 output transformer he had bought on sale from Clark Amplification a few years ago made for Mike Clark by Magnetics Components in Schiller Park, IL – a company that has been producing transformers since 1943, having been the primary supplier for Valco and various Gibson amps in the ’50s and ’60s. A call to the company revealed that ToneQuest ReportV12. N1. Nov. 20104the transformer Valco sent was essentially their replacement for a Deluxe Reverb, model #40-18002 without bell ends per Clark’s request. We also learned that the company offers a complete range of Classic Tone vintage power and output transformers, including a reverse-engineered clone of a ’55 Triad 5E3 output tranny, model #18022.

We also contacted Paul Patronete at Mercury and requested a ToneClone “brown Deluxe” output transformer, since Larry Cragg had provided them with specific measurements from original OT in Neil’s ’61 tweed Deluxe, confirming that it was indeed a ’61–’62 brown Deluxe tranny. With a total of 6 output transformers to listen to, we took the Deluxe to Jeff Bakos, who set up a rig on his bench that enabled us to clip in each transformer and very quickly switch back and forth between them as we played a guitar through the amp. Are we having fun yet? Here’s what we heard:

Lenco – An excellent authentic “vintage” vibe for those that prefer the classic, if somewhat murkier sound of a tweed amp being pushed, lots of sag in the low end and a jangly pop in the top. And “old,” rather “lo-fi” sound indicative of the ’50s era amps.

Magnetics Components Clark Deluxe 18002 – Similar to the Lenco, but stronger and more robust, with a prominent growling character and voice. Thick, wooly and willin’ with better treble presence and clear string definition then the Lenco, yet an entirely “vintage” character. This tranny is comparable to those found in Deluxe amps from the brown era through silverface. Excellent power, punchy and fat with exceptional clarity and tone.

Magnetic Components 5E3 Clone – Percussive and dynamic with a faster attack response than the Clark/Deluxe Reverb version, this transformer was reverse-engineered from an original ’55 Deluxe OT. IT imparts an intense, throaty tweed character with enhanced mid and treble presence, remarkable clarity, and an authentic vintage ’50s vocal tone with softer bass response and slightly less volume and power than the Deluxe 18002.

Allen/Heyboer TO20 – An interesting variation with a much more modern, percussive dynamic character. The sound was not as heavy and imposing in the vintage style, and with this transformer the Deluxe reminded us of the more refined sound of a Fender Princeton, with excellent dynamic punch for slide and Allen/Heyboer TO26 – As advertised, the low end held up loud and proud with very little sag and an audibly higher threshold of clean headroom, although beyond 6 on the volume control the Deluxe was still holding nothing back. Overall, this transformer imparts a cleaner, high fidelity tone with more clarity and stout bass response than a typical stock 5E3 transformer. An excellent choice for enhanced low-end and maximum volume.

Mercury Magnetics brown Deluxe – Immediately recognizable, the Mercury displayed a trademark sound that is smooth, exceptionally musical, warm and balanced. Sounding more “high fidelity” than the Lemco or Magnetic Components transformers, but still seductively unruly enough to get yer ya-ya’s out. Sweet, rich, detailed and sticky.

Now, you may be wondering why we would bother to audition so many output transformers…. How much difference can it make? Well, forty-odd years ago when someone rigged that old Stancor tranny in the Deluxe, the only choice available to most repair shops was whatever was on hand in the scrap pile. Today we can shape the tone and dynamic response of an amp with a variety of “vintage” or more modern, custom transformers that allow us to recapture the original sound and feel of the amp, or improve upon the original design. Why did Cesar Diaz install output transformers for a Twin Reverb in Stevie’s Super Reverb amps, and Bassman transformers in his Vibroverbs? Because the first thing that chokes and overwhelms a smaller output transformer are the bass frequencies, and Cesar wanted Stevie’s amps to produce a rock-solid, thundering low end that could handle his massive wound strings. The tone we’re celebrating with our ’59 Deluxe is quite the opposite…. The raucous sound of the amp teetering on the edge is the key to it’s exploding tone, but if you wanted to go in the opposite direction with more headroom and a tighter low end, transformers like the TO26 have been specifically designed for that purpose. We once replaced the output transformer in our Pro reverb with a bigger MercuryToneClone Bassman, and the Pro grained a tone of clean headroom and unyielding bottom. Wanna make it even harder still? Use a plug-in diode rectifier in place of the 5AR4 rectifier tube. No saggy britches now. As with so many choices we make in the Quest for tone, the final decision comes down to your mission and individual taste, and Jeff agreed that between the Heyboer TO26, both Magnetic Components trannies and the Mercury brown Deluxe, the question wasn’t which one was “best” – all four were exceptional, but different. Some players would prefer one over another for different reasons described here, but all of them represent stellar examples of just how far we’ve come since the day that old Stancor tranny was used to put the Two Fifty Nine back into service.

One last detail needed to be addressed…. Could we safely run the Deluxe with 5881s or 6L6s if we preferred that sound over 6V6s? Once again, we asked the prescient Mr. Valco for some Hoosier insight:

“The impedance mismatch in this particular amp using the 6L6s is really not a big concern, it won’t hurt the amp and will either sound good or it won’t. The 6L6s draw 1.8 amps and two 6V6s draw 0.9 amp, so using the 6L6s will add about 1 amp more current draw that the power transformer needs to supply from the 6.3 volt heater windings. On some small 6V6 amps, using 6L6s can and does cause the power transformer to run hotter because more current equates to more heat. The concern is that the power transformer in the Deluxe, not being a large one to start with, has the extra 1 amp of heater current capacity to safely use the 6L6s. One way to determine if the power transformer is really stressed out with the 6L6s is to measure the AC heater voltage on pins 2 and 7 on the power tube sockets (or on the pilot lamp) and see if the AC voltage drops significantly from the reading using 6V6s versus 6L6s. It should be a bit over 6.3 volts AC with the 6V6 anyway (since the wall voltage is higher these days than in the early ’60s) and with the 6L6s you sure don’t want to see a large drop in voltage below 6.3 volts AC. If there is a large drop it means the transformer is having trouble supplying enough current for the 6L6 heaters if given enough time with the 6L6s could damage the power transformer. If the drop is only a few 10th of a volt, and doesn’t go below 6.3 AC, then it would indicate that the transformer is supplying the demand for the heater current and should be OK. Most Fender amps used power transformers that could handle some extra current demand.

And now we arrive at the moment of truth. We’ve been steadily reeling in a parade of new and classic amps for review in these pages for 12 years now this month – Marshall, Fender, Magnatone, Hiwatt, Vox, Valco, Silvertone, Ampeg, Gibson, Gretsch, Mesa Boogie, Park, Supro, Dickerson, Traynor, Budda, Western Auto, Standel, Dumble, Cornell, Clark, Crate, Divided by 132, Reeves, Bad Cat, Gabriel, Fuchs, Koch, Star, Category 5, 65 Amps, Balls, Bakos, Callaham, Blankenship, Reinhardt, Grammatico, Siegmund, Chicago Blues Box, Roccaforte, Headstrong, Rivera, Mad Professor, Talos, Maven Peal, Reverend, BC Audio, Savage, Goodsell, Fargen, Carol-Ann, DST, Two Rock, Germino, Matchless, Louis Electric, Swart, Demeter, Juke, Aiken, Bluetron, DeArmond, Carr, Victoria, and Dr. Z, with more coming. Lots of amplifiers, multiple models from the same builders, and among the foremost classics – Fender, Marshall, Vox, Hiwatt, Gibson, Ampeg and the entire Valco catalog, we have acquired, optimized and restored dozens of amps considered to be among the most desirable vintage models ever built. In the 20 watt wheelhouse occupied by the Two Fifty Nine, it has no equal by a mile. Game over.

After a lot of back and forth testing with different sets of output tubes, we became hooked on the thundering sound produced by a pair of Philips small-bottle 6L6WGBs. Thanks to Larry Pogreba’s talent for scavenging rare tubes (in Montana, no less), we are flush with several outstanding and stout pairs of RCA 6L6s, but the brighter Philips really lit up the Deluxe with a fresh and lively attitude that mirrors the bounce of a newer amp. With the ’64 Jensen C12N loaded, the Deluxe spookily nails the tones of Neil Young’s rig on Ragged Glory – a “studio” recording cut live with the Deluxe and Old Black in a barn on Young’s ranch with Crazy Horse. With the volume backed off to 4-5 a bluesy jangle emerges anchored by solid low end, rich midrange, the sweetest treble tones imaginable, and variable levels of sustain and edgy distortion that can be controlled both by the volume on the guitar and pick attack. The Deluxe does not discriminate between single coils or humbuckers, ravaging both with equal fervor, and the responsive dynamic character of this amp simply is not of this world. Rotating the single tone control sharpens treble without dumping lows or mids, while also subtlety increasing gain, as if you were using a boost pedal. A “Y” cord plugged into the Instrument and Microphone inputs enables the two channels to be mixed with great effect. As Neil Young described, bringing the mic input volume up with the instrument volume set between 6-8 gradually deepens the tone while slowly igniting an intense explosion of thicker second order harmonics and distortion as the dynamic character of the amp softens. Pushing the Instrument volume level up into the 8-12 range brings the volume up to a perceived level that exceeds 20 watts, while provoking an angry, pissed-off cascade of astonishingly rich musical distortion as the notes swerve into controlled harmonic feedback.

Switching from the Jensen to the Celestion transforms the Deluxe into the most stunningly toneful 20 watt Marshall you could possibly imagine. To be honest, you probably can’t imagine it, because we have never heard anything like this ourselves, even after owning a couple of vintage Marshall PA20s, a rare Lead & Bass head and 1×12 cabinet, and a Balls 2×12 18 watt. We could easily live with either speaker, and the Deluxe also just kills pushing our 8 ohm 4×12 pinstripe cabinet.

For those of you who appreciate a somewhat tamer vibe, we can assure you that the Deluxe loaded with a fine pair of 6V6s is equally mind-altering. The overall sound is a wee bit smaller in girth and less imposing, yet abundantly overflowing with vivid harmonic depth, a supremely touch-sensitive response, and brilliant combination of fidelity, clarity and bloom. Compared to a black or silverface Deluxe Reverb, the ’59 presents a more musically complex soundstage, less harsh, stiff and linear, and it lacks both the sharper treble of a blackface amp, and the scooped midrange character. The tone is rounder and meatier, the treble sweeter and less dominant, with an enhanced 3-D image.

Now, if you’re the type that skeptically requires a qualifier to add a stamp of legitimacy to such an over-the-top review, here it is, Mr. Been There-Done That…. The Deluxe doesn’t and won’t spew big clean tones at stage volume. Our ’58 Tremolux produces a cleaner tone with a higher threshold of clean headroom by far at comparable volume levels, and the taller tweed cabinet encourages a stronger, cleaner resonant bass and low mid response. The Tremolux is also equipped with a Mercury ToneClone Tremolux output transformer, which creates a tone that is less wooly, raucous and indistinct.

The busted-up sound of the Tremolux above 5–6 is gloriously righteous indeed, but with more clarity and less provocative intensity than the Deluxe. Taken in context, what we’re suggesting here is that in our experience, the Deluxe has no equal as both a Fender and Marshall style 20 watt rocker (depending on speaker selection), and we’ll add “blues” to that description equipped with 6V6s and the Jensen C12N. During our 2-month test period, we also routinely used our Lee Jackson Mr. Springgy reverb, Analogman-modded Boss DD3 digital delay, and a very cool, versatile (and cheap) Flip tube tremolo pedal reviewed here. Can a modern replica of the 5E3 Deluxe deliver the same inspiring tones as the Two Fifty Nine? The closest thing we’ve heard is the Louis Electric “Buster,” but no, magical happy accidents like this Deluxe can’t be reproduced today – and that is as it should and shall always be. Quest forth…

View PDF Article

Like the pedal business, the number of amplifiers being built by smaller builders has mushroomed into a garage and basement Skunkworks industry that is constantly changing. New guys pop to the surface and ride the momentum created by chat rooms and social media, while others quietly slip beneath the surface in an unfortunate imitation of Beach Boys drummer Dennis Wilson, never to be heard from again. The desire amongst certain guitarists and collectors to own the latest, supposedly greatest new amplifier is a power drug, and for some, a hard habit to kick. We enjoy discovering small batch alternatives to familiar archetypes and affordable production amps, too, but since we’re doing so on your behalf, our initial evaluation process lacks the unbridled enthusiasm of a new owner who has already made the plunge financially and emotionally. Still, when a giddy reader calls or writes asking us to review their new killer amp, we routinely hit the builder’s website, send an introductory email and wait for a response. Such was the case with the Tungsten Cremawheat and builder Adam Palow

Ultimately, the Cremawheat turned out to be another exceptional amplifier as our review reflects, but as is so often the case, the story behind the name on the face plate is as interesting as the amp. Listen….

TQR: You mention on your website that you were inspired and intrigued many years ago by your first tube amp. Do you recall what it was?

It was a 1965 Fender Vibro-Champ that was missing the face plate, and the grill cloth had been replaced with a red and black check material that looked like it had been on a sofa. I think I was around 16 when I got it, and no matter what I played through it, the amp sounded very musical compared to the solid state practice amps had used before. It was the beginning of an obsession. I started chasing down vintage Fender amps wherever I could, and I met a guy who showed me how to safely drain the stored voltage in an amp, how to use a soldering iron, and he explained how bigger caps produced more low end. From that point forward I was on my own, and everything I have done since has been the result of trail and error and experimentation. I’m limited in some areas because I don’t necessarily understand all the theory, but in another sense it’s empowering because I am chasing feel and working in an intuitive way rather than strictly by the “book.” My favorite part of the build is constructing the board and wiring the chassis. If there is any artistic expression in building an amplifier it’s in the way the board is constructed. Of course, in the larger picture, it’s completely meaningless.

TQR: What were the most significant things you learned through hands-on experience working with guitar amps, and the five years you spent working on Hammond organs with Bob Schleicher?

The thing that blew my mind the most once I had acquired multiple identical models of the same amplifier like the Fender Blackface Bassman and Bandmaster was how different they could sound from each other even though they were built with the same components. That also carried over into my work with Hammond organs, because every large Hammond console also had its individual voice, and I attribute that to the accepted variance in parts values, and individual and very unpredictable drift in these values over time. You also see random parts stacking where some of the capacitors may have been oriented the correct way and others not. When all the caps are pointing the right way you can have an amp that sounds faster, and when they are oriented the wrong way the amp can sound slower. On the old caps there was usually a band marking the outer foil, and whether or not they were oriented correctly often just seems like chance. Some companies paid strict attention to that and others did not. Even if I am building ten identical amplifiers in my own line, there are going to be variances between them – not only in the tolerance stacking, but in the way the tubes bias to the cathode resistor. I have an absolute minimum standard – it has to inspire me or I’m not going to ship it out, but every once in a while you drop in the right rectifier and the right power tubes and they just match up perfectly with the cathode resistor and it makes your hair stand up on end. Magical. Yet that same amplifier with a different set of tubes may not do the same thing.The Hammond organs are unique because not only do they have an extremely rich and harmonically complex signal, but they have infinite sustain with no transient attack unless you’re using the percussion feature, so when you’re dealing with Leslie power amplifiers you’re not dealing with sag. You’ve got compression going on because you’re driving it with a very wide band signal, but because there is no transient, you’re not experiencing sag, compression and release in that order. I spent a lot of time rebuilding Leslie amplifiers, and there was a very specific type of distortion coming from those 6550 Tung-Sols – a low, grinding, wooly distortion kind of like the Marshall of the organ world in a lot of ways, and I caught that sound in my head. It was very musical, and it had a lot of clean qualities, but also an outrageous amount of overdrive on tap, and even when it was driving hard there was still enough clarity to retain a musical quality in the distortion. You could really hear the notes and the intervals between them, and that’s the complaint I had with a lot of amplifiers outside the vintage world…. They swung so far into breakup and distortion that you lost the clarity of the notes. There was more noise than tone, and the place I’m coming from is a more musical place. The other aspect of my work with Hammonds is that I gained a huge amount of experience with vintage Jensen Alnico speakers.

TQR: We have always wondered if the Jensen speakers used in Hammond cabinets were similar to those made for guitar.

In the Leslie, the Alnico P15LL and later C15NLL bass driver that shoots down into the rotating horn were definitely not guitar speakers by any stretch. The 12 inch Jensens I’ve seen bear all the same markings as standard Jensens for guitar, the differences being that they have black frames with no Jensen sticker, and the Hammond code starting with the letters “AO” have been silk-screened on the frame. I have pulled P12Ns out of old Hammond A100s, as well as P12Qs, and if they were specifically designed for organ, they are also the best sounding guitar speakers I have ever heard, and I have used them to base my own speakers on made by Weber.

TQR: Which prompted the development of your own line of proprietary speakers?

Yes, and I didn’t really have to start from the ground up because they had already come close to the mark, but I wasn’t hearing the same extended frequency response that I was hearing from the vintage speakers, and it was just a matter of developing a different recipe. Fortunately, when Ted was still alive we went through the process of mixing and matching components, just trying to get that sound. I didn’t care if the parts were period-correct – I just wanted them to sound right. I tried to do the same thing with the ceramic line, but we just never nailed it and I never put them into production. Of course, the goal in developing the Alnico speakers was to produce the low-wattage, medium fidelity, $6 replacement speakers that they were originally.

TQR: Looking at the different models you build today, it’s obvious you prefer the sound of tweed-era amplifiers.

Yes, I cut my teeth on blackface amps, but when I built my first tweed Champ I became one of those guys that ditched my pedalboard and plugged straight in. For me it’s all about that very alive midrange, and the dynamic response you get out of the power section. I was instantly hooked. I also have a fondness for the lower power brown amps as well, but when it comes to what I personally want to plug in to and play, I really need to feel the response of a tweed power section.

TQR: What’s your approach to specific types of capacitors used in building your amps?

You have to let your ears be the guide, and everyone hears things differently. Every quality capacitor has its place, but I personally prefer the sound of Mallory 150s in tweed amps. Other people feel that they are too bright in the upper mids until they break in. I tend to break in my amplifiers for 72 hours and when I take breaks from building I’ll plug into every amp that’s burning in. The truth is, everything matters. In the Cremawheat, for example, there different capacitors are used in the tone circuit to color the tone in a certain way. It’s one recipe. I also use custom-wound Mercury Magnetics transformers in everything. Some of them are custom-wound because I wanted a different gauge of wire, and others because I wanted a different secondary voltage. When we’re talking about power transformers, voltage that you’re sending out to the circuit makes much more difference than the brand you’re using. With output transformers it becomes more critical. Some people want to hear a darker transformer, others high-end clarity…. Some people want a smaller core so it saturates sooner, and others want enough iron so that it never saturates. All of those factors play not only into the sound, but they hugely affect feel.

TQR: Can you briefly summarize each model you build?

The 8 inch version of the Mosaic comes with either the stock 5F1 (Champ) output transformer or the oversize version, which nets you perhaps an additional 2 watts. You get more punch rather than volume. I also build a 12 inch Mosaic Mark II with an additional tone knob, which gives you more bass.

The Cortez was intended to be my flagship model until the Cremawheat came out. The name was inspired by Neil Young’s Suma album – you can just hear the tweed all over it. Its 12W-15W with 6V6s and it bumps up to about 18W with 5881s or 6L6s. It’s basically a straight-ahead 5E3 design.

The Cremawheat is my attempt to retain the tone and feel of a great 5E3 Deluxe, while giving you the dynamic range that would otherwise be lost in the output transformer and speaker with that amp. Those were two choke points on the 5E3, and the third being the massive amount of bass that’s being sent through the circuit, which causes it to distort so early. The other significant feature in this amp is the British-voiced Scumback speaker. It adds punch to the dynamic range, and enough bass, but not the ragged and loose 5E3 style low end.

The T35 covers the 5F4, 5E5-A and 5E7 circuits for the Bandmaster, Pro and Super. They were basically the same chassis with a couple of minor resistor changes and three different speaker configurations, and I tend to prefer the 1×15 and 3×10 versions. It’s the only fixed bias amp I offer. I like the T35 series, but I tend to gravitate toward the cathode biased amps and most of my customers seem to as well.

If you took the 2-input ’55 Bassman, which shares a lot with the Super, Bandmaster and Pro amps of that era, and cathode biased it in a 2×12 speaker format, that’s kind of where the Blue Point sits. When you pay it clean, it sounds very American in the style of a mid-’50s Bassman, and as you turn it up, you get more coloration from the British-voiced speakers. It starts to cross the Atlantic into that early JTM-45 Bluesbreaker tone, but stops short of a later Plexi amp.

The Buckwheat is the follow up to the Cremawheat. It’s a 6L6-based, 30 watt with the Scumback H-75, which is their version of the pre-Rola G12H. It has a significant amount of headroom over the Cremawheat, and the speaker produces a glassier, high-headroom tone with a bigger transformer and a larger cabinet that leaves more air around the notes. If you’re a Telecaster player, for example, who wants more headroom with just a little hair, this is that amp.

TQR: Will you build specific amps with different speaker configurations as a head or combo, and what is the current lead time for an amp?

Sure, I’ll absolutely build variations on the stock models – I actually really like the 16 inch Mosaic and I have built several of them. I want to know that I’m building exactly what a customer wants. The lead time right now is eight weeks, and I always try to keep it under three months. I sell direct, and through a small dealer network, but I do enjoy working directly with customers. Depending on what a customer wants, I may suggest a specific change to the stock circuit, and I find that interaction very rewarding Introducing another 15W–20W amp in these pages is nothing new – in the past year we’ve invested a log of ink highlighting amps like Jeff Beck’s choice of a Pro Junior, our vintage ’59 Deluxe and ’76 Princeton Reverb, the Retro-King 18W and the Trace-Elliot Velocette. Why? Because we understand that such friendly decibel levels offer adequate volume for use in small clubs, mic’ed on bigger stages, yet till fill your house, studio or practice room with a mighty roar when needed. Small amps just make more sense today for most players, but like us, you might be wondering just how many ways a smallish guitar amplifier can be designed and built to produce a genuinely unique voice and vibe. You know what you’ve already got, but what might you be missing, and at what point does your quest to discover the ultimate low power amp become redundant, at best? A fair question, and given the nearly infinite variables created by the marriage of different components within different circuit designs, we are happy to report that we haven’t reached the end of the road in the quest for tone quite yet.

Viewed within the board context of the booteek amp landscape, the Tungsten Cremawheat emerges from the box as an uncommonly attractive natural blonde. Offset with gold grill cloth, it scores big in style points without even being lit up. Nor will you find any self-conscious bells and whistles added to an otherwise classic design, as if the builder wanted to get noticed by adding the kind of stuff we seldom really use – like Selmer-style rotary tone switches, pentode/triode modes and toggled boost switches (although Carr has always done those right by bypassing the tone stack). Indeed, this amp is so outwardly attractive, approachable and comely that pulling the back panel off might inspire distant memories of an anticipation experienced in concert with a one-handed thumb and forefinger bra removal technique. (We now pause to allow a moment of fond reflection. Please take your time.) Adam Palow’s skill in assembling and soldering up a circuit board culminates in nothing less than a work of art. Flip the chassis over and the custom-wound Mercury Magnetics trannies provide further evidence of Palow’s commitment to following his muse. In practical terms, you get four inputs into two channels (bright and normal), volume/volume and tone, plus a standby switch and extension speaker jack.

Our first session with the Cremawheat was agreeable enough, but repeat visits left us with a nagging impression that something was either missing, or perhaps technically present, but not being fully reflected in the sound of the amp. Naturally, we used our tweed Tremolux and Deluxe for benchmarks, and the Tungsten sounded subdued and restrained by comparison. We tried different tubes first with no appreciable change, and that’s when we focused our attention on the Scumback speaker. Admittedly, we had suspected it from the beginning, so with the original tubes back in the amp, we connected the Celestion G12H30 70th Anniversary in our ’59 Deluxe cabinet to the Cremawheat, fired it up, hit a big E chord raking a heavy Pyramid pick over the strings slowly, followed by ten minutes of unbridled delirium. Paired with the Celestion, the Tungsten bowed up with increased volume, clarity, dynamic punch, and a gloriously rich tone that easily rivals that of our Deluxe, but with a little more added sparkle. Swapping the stock Electro-Harmonix 6V6s for a pair of RCA 6L6s brought the Cremawheat to climax with an even bigger, more imposing voice, precisely in the style of our ’59. If anything, the Tungsten offered a slightly more defined and chiseled tone as a new amp should when compared to one that has undergone a half century break-in period.

To be fair, we called Adam Palow to inform him that while we absolutely loved the Cremawheat, we were not feeling the Scumback. He agreeably acknowledged that the Scumback was indeed somewhat more subtlety endowed than the Celestion, which is why he offered the G12H as an alternative for players desiring maximum girth, power and growl. Any number of modern speakers would surely sound outstanding in the Cremawheat – but we clearly preferred the more vivid soundstage created by the Celestion when the choice is narrowed to one of the two stock speakers offered. Would we buy and play the Cremawheat? Absolutely. It now reigns among the best on temporary boutique twenty watters, and in four important respects (tone, overall clarity, availability and price), the Tungsten impressed us as an irresistible alternative to a vintage Deluxe and any and all modern replicas

View PDF Article

While Michael Bloomfield was playing cranked up blonde Fender Bassman and blackface Twin Reverb amplifiers, Marshall 100 watt stacks suddently appeared thanks to The Who, Jimi Hendrix, Cream and Led Zepplin. Throughout the ’70s, rock was dominated by the sound of a Les Paul and Marshall amps, but despite its reputation as the ultimate rock machine, all four-input, 100 watt Marshall model “1959” heads are not the same….

The first 100 watt Marshall amps appeared in late 1965,and despite Marshall’s decision to drop tube rectifiers for the less forgiving, harder sound of solid state diode rectification, the “Plexi” 100 watt heads remained more closely related to earlier Marshall amps inspired by the tweed Bassman than the Super Leads that would follow. In the early ’70s, the 50 watt model “1987” head and 100 watt Super Lead were gradually modified to produce more gain faster, and the bright channel was pushed to a punishing level of thin, ear-shattering brightness, while Channel II remained too dull and bassy to be used alone.

We acquired a 1973 Super lead—the last year before Marshall switched to printed circuit boards—for the modest sum of $1,000, made possible by a recent Dagnall replacement output transformer. Two .022 mf caps had been replaced with Orange Drops and another removed altogether in a futile effort to reduce brightness and gain—other-wise, the original Super Lead circuit remained intact and unmolested. Our plan was to run the amp at approximately 60 watts with just two EL34s, requiring the amp to be set at half the rated speaker impedance of our 8 ohm 4×12 Avatar cabinet, loaded with two Celestion Gold Alnico 12s and two “Hellatone” 70th Anniversary G12H 30s.

As we discussed this project with Jeff Bakos, he mentioned that the 100 watt Super Leads not only sound very different from the 50 watt heads in ways that transcend a mere increase in power, but he also felt that the 100 watt Super Lead amps sound better with just two powertubes instead of the full compliment of four…“That’s very common down here—I know a lot of layers who prefer that sound.” We also consulted with Sergio Hamernik of Mercury Magnetics on a suitable replacement for the modern Dagnall OT, and he suggested the ToneClone’69 Marshall self-leaded version. “Self-leaded” means that the actual wires wound within the transformer are extended to connect directly to the amp, rather than smaller diameter lead wires being attached to the transformer internally. Installing a self-leaded version is a bit of a bitch, since you are cutting and bending much heavier gauge wire to fit in tight spaces, and the insulation must be scraped off the wires before soldering. But Jeff had been here before,and all was taken in stride.

We also noted that the original power transformer in our ’73 Super Lead was similar to those found in the early Plexi100 watt amps with plate voltages well above 500 volts.

Our amp measured 522 volts, while the plate voltage on most post-plexi 100 watt “1959” amps are usually lower—around 460 volts. The “hotter” transformer in our Super Lead produces a comparatively higher and less compressed distortion threshold, and if not for our pair of NOS MullardEL34s, we might need to be more selective about choosing current production tubes that can withstand +500 volts on the plates. Jeff was confident that JJs would hold up, less confident of Svetlanas.

We took the Marshall home and initially ran it with three spare Telefunken 12AX7s just to see if they sounded as sterile in a guitar as we had recalled in the past. They do. We could hear a distinct improvement in the mid and bass tones with the new transformer, but the bright channel remained far too bright to be used alone, even with a Les Paul. While we could manage to knock down some of the treble and acquire a decent tone with the bright channel set on “3” and the bass channel patch with the volume on “6,”pushing Channel II so far above the level of bright channel introduced an indistinct woofiness we didn’t care for. The next day we returned to Jeff’s shop for his standard Marshall 4-banger input channel mod, which simply involves moving the original .005 mf bright cap on the bright channel to the basier Channel II. We had done this before with our ’69 50 watt and a vintage PA20, and it unerringly transformers the sound of the notoriously dull Channel II to a fat, warm, musically rich and bright sound that works perfectly every time. We also replaced the two Orange Drop caps with Mallory 150s and pulled the super hi-fi Telefunkens, replacing them with NOS RCA 12AX7s—the warmest, creamiest pre-amp tube ever made.

With the Super Lead thus optimized and tweaked, its voice was transformed from an angry soprano chain saw to a classic Marshall with all of the requiste thick,rich, historic hall of fame tones at our fingertips. We could mine brilliant clean tones on “3” at a usable volume level that revealed all the gorgeous detail of the vintage patent number pickups in our Historic Les Pauls, and our Stratocaster, Nocaster and Les Paul Junior all sounded equally good. Add Fender outboard reverb and you do indeed have the Twin from Bloody Hell.As Jeff predicted, the big power supply in the Super Lead also produced a much more formidable and impressive presence than a typical 50W. Yes, the Super Lead is still a beast, tamed for your consideration and our enjoyment. But if classic Marshall tone is the sound you crave, a properly groomed Super Lead is hard to beat, and given today’s boteek and vintage amp prices, it’s a solid steal.

View PDF Article

Fender designed and built more than one transitional, non reverb blackface combo amp that would soon acquire reverb and a new name, including relatively small numbers of blackface Princetons, 4×10 Concerts, 1×12 Vibrolux and 1×15 Pros. We acquired a 1×15 blackface Pro, and while it ultimately proved to be an extraordinary exceptional amp, we were also reminded of the potential pitfalls that exist when buying old amps sight-unseen, as well as the potential rewards.

We found the ’64 Pro listed on eBay and bout it from a dealer after requesting a detailed photo of the chassis and circuit. Proudly described as “the best amp in the store, “the rare ’64 blackface Pro is essentially a blackface Vibroverb without the “verb.” Do we have your attention yet? Three caps had been replaced, the original baffleboard had been professionally converted to plywood with the original grill cloth remaining intact, and an on/off pot had been installed for the tremolo intensity control that bypassed the tremolo circuit when rolled to “1” with a click, adding gain that would otherwise be missing in the Vibrato channel. We pulled the JJ power tubes and assorted Russian pre-amp tubes and replaced them with lightly used,“test new” RCAs from our stash, rebiased the amp and fired up the Pro….

Sounded like shit. We had been here before with a dead-mint ’64 Vibroverb bought years ago that had passed through a certain amp guru’s hands in Pflugerville, Texas.How could a vintage Fender sound so bad we wondered? Turned out that the value of the bright cap on the Vibrato channel had been changed on the Vibroverb, rendering a thin, scalding tone that would have given Ed Jahns fits, as it did us. Changing the bright cap back to spec immediately restored the Vibroverb to its rightful pace in history, but the Pro had other problems….

The baffleboard swap and added switch on the tremolo intensity control were clues that someone had also spent time troubleshooting the amp, probably trying to detect the cause of the Pro’s weak output, thin tone and curiously harsh edgy distortion. The amp just didn’t sound right. We pulled the original, reconed Jensen C15N dating to 1964 and subbed in an Eminence Legend, but the Pro still sounded choked-off, linear and wrong, so it was off to Jeff at Bakos Amp works on the Friday afternoon before Memorial Day weekend in a frog-chokin’ Georgia thunderstorm. When the going gets weird, the weird turn pro…..Now, this is the difference between someone who really knows his craft and a hack….Jeff plugged his bench guitar into the Pro, hit a couple of chords, issued a single grunt of displeasure and caustically observed, “Something is definitely fucked up.” With the chassis on the bench, Jeff scowled at the choppy sine wave the amp produced on his scope as he checked voltages with his multimeter. “I think the output transformer is going down slow—it measures 11 volts and it should be reading 16….” He clipped in a substitute OT from a stout old Fisher hi-fi, plugged in and hit a chord… “That’s closer to what it’s supposed to sound lie….” And sure enough, the missing lows and mids were present, the raspy treble tones were subdued, and for the moment, the Pro showed promise. We called Paul at Mercury Magnetics and ordered a black-face Pro Tone Clone replacement trans-former, shut it down and wished each other a good holiday. A week later the Mercury Magnetics replacement output transformer had arrived. Jeff wired it up, and then turned his attention o three silver mica caps that had replaced the original ceramic caps in the phase inverter and tone circuits. Jeff: “Somebody probably read an article about how these would bring the high end up, but I prefer the ceramics—always have. Besides the effect of the voltage from the old output transformer being low, these silver mica caps were contributing to that brittle tone we were hearing. They are the wrong value, and they changed the entire sound of the amp.” Jeff pulled all three silver mica caps and replaced them with the correct ceramic disc caps, and since an on/off switch had already been installed for the tremolo, we mounted the 25K mid range pot in the back panel hole for the extension speaker jack. With the Pro now thoroughly put right and the midrange pot added, Jeff hit a few chords, moved the EQ and volume settings around a bit in both channels, smiled and said, “That sounds really good. Yeah, that’s it.”

Back in our music room, the final step was to re-bias the Proat 34mA with an AmperexGZ34 rectifier and our last pair of vintage RCA black plate 6L6s, which in unused, new old stock condition have soared to $400/pair. The re-labeled Tube NOS Phillips JAN 6L6 WGBs we had tried sounded good—but the smooth warmth, exceptional musicality and deep harmonic content of the RCAs just can’t be beat, and it is a difference you can definitely hear. Smoke ’em if you got ’em….

We lit up the Pro with the ’63Fender Reverb unit and reverently smiled at the jaw-dropping tones pouring from the big Eminence Legend 15. Imagine the sound of a slightly kinder, warmer sounding 40 watt Super Reverb void of the sharp, penetrating treble presence that has sooften left our ears ringing for hours after a tumble with a blackface Super. The sound of the ’64 Pro is all Fender, with solid bass that doesn’t fall apart at high volume as the smaller blackface combos can,sweet, singing treble tones, and now… a mid range control that can gradually push the amp beyond its original, clear and liquid “scooped” mid range voice to an exceptionally thick, “mid-Atlantic” roar that unleashes heavy sustain and rich, musical distortion as only a Fender can. The Pro brilliantly complements every guitar we own, producing the essence of classic Stratocaster, Tele, P90 and humbucker tones with clarity, depth and lush fidelity that literally fills the room. Yes, there are different and equally worthy tones to be had from the British classics,but we have never heard a more beautiful sounding or versatile Fender amp—one that can range from crystalline, blackface clarity to the full burn of an early blonde Fender Bassman at much friendlier volume levels. The Pro can get plenty loud, but it’s a loud that doesn’t kill you in the style of a Showman, Twin or a Super Reverb.

The irony in this unexpected discovery has not escaped us,and perhaps the weight of it is now becoming clear to you, too. This project did not begin well, and we confess to experiencing some remorse when the Pro arrived with a few bad mods, weak and thin from the original output transformer going down, and generally just sounding very wrong. Our dismay was soon displaced by genuine enthusiasm; however, as we were reminded that this is indeed what the quest for tone is all about it. We’ve acquired absolutely bone stock amps in perfect working condition that just couldn’t tote the note, so why should we expect to buy a 44 year old amp that’s been played without it needing a little repair and restoration work? The end entirely justifies the means.

Having finally experienced the Pro’s singular, exceptional sound, we wondered what had caused it to be relegated to such obscurity among all the Fender black face amps. Like the Vibrasonic and Vibroverb, perhaps it was doomed by the presence of the single 15” speaker. Like the Pro, the blackface Vibroverb 1×15 was produced for less than a year, and with the introduction of the 2x12Pro Reverb in 1965, Fender would no longer produce a 1×15 combo until the introduction of the silver face Vibrosonic in 1972. Yet, the earlier 1×16 Pros had been Fender’s flagship amps during much of the tweed era, and in 1960 the 1×15 brown Pro ranked second only to the1x16 Vibrasonic in the Fender catalog. Somewhere along the way, the 1×15 combo had clearly fallen out of favor with Fender, guitarists, or both, and given the short life span of the Vibroverb, even the addition of reverb couldn’t save it.

Twenty years later, Stevie Ray Vaughan elevated the Vibroverb to hall of fame status, otherwise, the 1×15 com-bos seem to have been perceived as “uncool” for anything bug jazz and blues, as if wearing a jacket and tie were required to play them. The Pro is a great blues amp, but it’s also a great rocker, and equally well-suited for jazz, pop and country. With far more clean head room and power than any tweed Pro and much stronger distortion, sustain and dynamic character than a brown Pro, the blackface Pro reflects Fender’s ongoing pursuit of more powerful, cleaner sounding amps, but unlike the black face Bandmaster, Tremolux and Showman, and Pro can really rock the house cranked. We suspect it’s a single 15 and missing ’verb that throws people off today, yet in’64 Pro shares its DNA with the ’64 Bassman and all the highly prized blackface combo amps, including the Deluxe Reverb, Vibrolux Reverb, Super Reverb and the heavily prized and hyped Vibroverb.

The contrast between the Vibroverb’s Holy Grail status versus the lowly blackface Pro simply underscores how easily we can be blown off course by what isn’t hyped on the Internet or in print, and by the powerful logic that suggests if anything 44 years old is truly noteworthy, “we” would already know about it. Well, apparently “they” don’t. But you do. Blackface Pros can be found for $1 500–$2,000,with originality and overall condition driving prices accordingly. Like the Deluxe, we wouldn’t buy one that has had all the blue molded capacitors or Allen-Bradley resistors replaced, but the transformers available today from Mercury will sound every bit as good or better than the originals, and as we have said so many times in the past,the Eminence Legend 15 is spectacular. Add some good,current production or NOS tubes and you will have been delivered to a place well beyond the common man’s limp and shriveled imagination. Now Quest forth….

View PDF Article

4H / 500mA Choke — Fender Tweed era Part # 14684 — 3 1/8″ center to center

*This choke is for Tweed era amps such as Bassman & Low Power Twin (not a Champ!)

Tweed — #14684 — **Used in early Tweed amps w/ dual rectifier tubes

2.84 Henry, 400 mA current rating

Vertical mount — bolt hole spacing of 3 1/8″ center to center

59 Tweed — with separate, insulated bias winding — 100V, 120V, 220V, 230V & 240V primary

’59 Tweed

’59 Tweed — lower B+ — 220V, 230V & 240V primary

’59 Tweed — Universal Voltage Primary

59 Tweed — lowest B+ — 100V, 120V, 220V, 230V & 240V primary

59 Tweed — 275-0-275 unloaded B+ — separate bias winding

59 Tweed — 275-0-275 unloaded B+ — separate bias winding — 220V, 230V & 24V primary

’59 Tweed — lowest B+

’57 Tweed — #7993

’55 Tweed — bias tap — #7993

’57 Tweed — #7993 — Universal Voltage Primary

’59 Tweed — Lower B+ — with Universal Voltage Primary

Tweed — 4 & 8 Ohm taps

Tweed — 4, 8 and 16 Ohm Secondary — Oversized Upgrade!

Tweed — single 2 Ohm tap

’59 Tweed — #45249 — single 2Ω secondary — bolt hole spacing w/ L-bkts is 2 1/4″ x 3 1/8″

Optional “Especial” bracket is 2″ x 3 3/8″

Larger size — Tweed era — 3.5 Henry — 3 1/8″ Mounting Centers

3.5H / 200mA Choke — Fender Tweed Era Part #14684 — Small size — 2 13/16″ Mounting Centers

’59 Tweed — 4 kOhm primary, 2 & 4Ω taps

Bolt hole spacing w/ “Especial” bracket is 2″ x 3 3/8″ (L-bkts is 2 1/4″ x 3 1/8″)

You want amps? You had ’em at the 2009 NY Amp Show! Loni Specter ran another trouble free amp extravaganza at the Embassy Suites Hotel in Piscataway, New Jersey. There were approximately 64 exhibitors showing their stuff to hundreds of guitar players in attendance. So many goodies, so little time. All right let’s get down to who we had the pleasure to meet and sample some of their creations.

Now with my head spinning a little from checking out all this cool gear a small pile of daphne blue Tolex amps caught my eye. This was the Nolatone suite. Paul Sanders is the builder and designer of the Nolatone amps. He brought along the Chimey Limey (can you say fat AC15?) that has a switch on the back of the chassis to select either a 12AX7 or EF86 for the first gain stage. The 5 watt June Bug which has 3 gain stages for thick sounding overdrive and a removable baffle ring to accommodate a 10″ or 12″ speaker. And last was my personal fave the 22 Tango. This was one of the loudest, clearest 2x6V6 amps I ever heard. It reminded me of a tweed Bassman tone with tone stack controls that were much more effective. Paul says that the big, clear sound has to do with the special Mercury Magnetics RSO-type output transformer. Whatever the recipe is it sounded great and had a big amp feel to it.

’58 Tweed — 100V, 120V, 220, 230V & 240V primary

58 Tweed — Triad 8087 size — same as ’59 — with bias tap coming off B+ winding

59 Tweed — Triad 8087 size — same as ’58 — with separate, insulated bias winding

’58 Tweed — lower B+ — 100V, 120V, 220, 230V & 240V primary

’59 Tweed — lower B+

’59 Tweed — 2, 4, 8 & 16Ω taps — UL taps

’57 Tweed — smaller size — #2485

’59 Tweed — 4 kΩ primary, 4 & 8Ω taps

Bolt hole spacing w/ “Especial” bracket is 2″ x 3 3/8″ (L-bkts is 2 1/4″ x 3 1/8″)

’59 Tweed — 4 kΩ primary — 4, 8 & 16Ω taps

Bolt hole spacing w/ “Especial” bracket is 2″ x 3 3/8″ (L-bkts is 2 1/4″ x 3 1/8″)

’59 Tweed — 2, 4 & 8Ω taps